低压螺杆空压机
关键词：低压空压机，空压机低压，低压螺杆空压机，螺杆低压空压机，低压压缩机，低压空气压缩机
低压螺杆空气压缩机
产品详情规格参数留言
低压螺杆空气压缩机产品型号/报价/及技术参数
Low Pressure Screw Air Compressor
产品特点/ Product Features
0.3Mpa 低压螺杆空气压缩机
Low Pressure Screw Air Compressor
● 排气压力 / Working pressure：0.3Mpa
● 排气量 / Air delivery：6.55-92.04m3/Min
● 电机功率范围 / Motor power range：22-355 Kw0.5Mpa 低压螺杆空气压缩机
Low Pressure Screw Air Compressor
● 排气压力 / Working pressure：0.5Mpa
● 排气量 / Air delivery：6.55-55.73m3/Min
● 电机功率范围 / Motor power range：30-250 Kw
为纺织、水泥、玻璃行业专门打造的/ Especially design for textile, cement and glass industry
德耐尔 50Hz 0.3Mpa
低压螺杆空气压缩机www.51kyj.com
当您的用气压力为 0.2--0.5Mpa 时，选用常规的 0.7Mpa
空气压缩机将造成巨大的电力浪费，选用低压螺杆空气压缩机
在同样的电机功率下可以大幅度增加压缩空气的产气量，相应
地，您可以 ----- 省电 20-50%。
如果您购买 0.7Mpa 的机器，而实际使用压力 0.3Mpa 的
话，它的工作过程通常是这样的：螺杆主机先将空气压缩到
0.7Mpa，再通过减压阀等途径将压力减到 0.3Mpa 使用。也
就是说，您使用的是0.3Mpa 压力，您承受的是0.7Mpa 的功耗。
也可以从排气量方面加以证明：
一台 132kW、0.7Mpa 的螺杆空压机，它的排气量应该
是 24m3/min。而选用 132kW、0.3Mpa 的螺杆空压机，它的
排气量超过了达到了 39.8m3/min ！所节约的电费将让您在不
到一年的时间内收回投资。
根据用户的使用压力，自动调节内压缩比，在 0.2~0.5Mpa
的排气压力范围内，都能保持比功率（能效）。
采用油泵强制润滑
确保在极低的排气压力下也有足够的喷油量、的油气
混合比 DENAIR 50Hz 0.3Mpa low pressure screw air compressor
It will cause a terrible waste of electric power to choose a routine 0.7Mpa
air compressor when the pressure consumption is 0.2-0.5Mpa. Choosing a
low pressure screw air compressor can enlarge the air delivery of air compressor
under the same motor power. Corresponding, low pressure compressor can help
you save 20% to 50% electric power.
If you purchase the 0.7Mpa compressor, but your actual use pressure is
0.5Mpa, its working process as follows: the screw air end firstly compresses
the air to be 0.7Mpa, then reduces the pressure to be 0.5Mpa through pressure
reducing valve or other approaches. That is to say, you use 0.5Mpa pressure, but
enduring 0.7Mpa power consumption.
It can be also proved by air delivery:
One screw air compressor of 132kw and 0.7Mpa, its air delivery should
be 24m
3/min. However, if choose DENAIR 132KW and 0.5Mpa screw air
compressor, the air delivery can reach 30m
3/min! The saved power fare can
recoup your capital outlay within one year.
As per users’ working pressure, it can automatically adjust the compression
ratio, and within the exhaust pressure range of 0.2~0.5Mpa, the best specific
power can be maintained. (energy efficiency)
Using oil pump force-lubrication.
Make sure the adequate oil injection and best oil-gas mixing ratio under the
very low exhaust pressure.
