混流泵使用与保养：Use AndMaintenance? ? 1、经常检查轴承温度，轴承箱内应装70%的钙基黄油，不得过多或过少，轴承升温一般不得比周围超过35°C，轴承的极限温度不得超过75°C（用手摸感到烫手），若超过应停车检查原因予以消除。Check the bearing temperatureregularly.The bearing box should be put 70% butter，it can not be too much ortoo little.The temperature rising of bearing can not be more than 35°C higherthan around temperature and the limiting temperature of bearing is 75°C，if the temperature is higher than 75°C， stop to check the reason and adjust it. 混流泵按用途分类输送泵、循环泵、消防泵、试压泵、排污泵、计量泵、卫生泵、加药泵、糊化泵、输液泵、消泡泵、流程泵、输油泵、给水泵、排水泵、疏水泵、挖泥泵、喷灌泵、增压泵、高压泵、保温泵、高温泵、低温泵、冷凝泵、热网泵、冷却泵、暖通泵、深井泵、抽气泵、血液泵、抽料泵、除硫泵、剪切泵、研磨泵、燃油泵、吸鱼泵、浴缸泵、源热泵、过滤泵、增氧泵、洗发泵、注射泵、充气泵、燃气泵、美工泵、加臭泵、切碎泵开车顺序：? ? 1、关闭出口闸阀? ? 2、将水注入水泵，以排除进水管及泵内空气，可从泵体顶端引水杯注入清水，12尺混流泵，也可用真空泵注水（开动真空泵，混流泵，排除水泵及管内气体在水充满水泵的同时，起动水泵，打开闸阀，停止真空泵）。3、开启电动机（注意水泵的旋转方向）。? ? 4、当电动机正常运转后，逐步开大闸阀，达到所要求的工况后，调节填料松紧。若水泵运转，轴承温度等都正常，则可继续运行。III. ?StartingSequence? ?1.Close the ouletsluice valve.? ?2. Injectwater into pump to remove the air in water-in pipe and pump which can realizedby injecting clear water from the water diversion cup of the pump body end orby vacuum pump(start the vacuum pump， remove the air from pump and pipes， startthe water pump when the pump is full of water， open the sluice valve， stop thevacuum pump).? ?3. Start themotor(pay more attention on the rotation direction of pump)? ?4. When the motor runs normally， turn up thesluice valve gradually，混流泵厂家， adjust the tightness of padding when gettng to therequired working condition.If the pump runs well， the temperature of bearing isnormal， and it can run sequentially. 12尺混流泵-混流泵-金石泵业(查看)由泰安金石泵业有限公司提供。泰安金石泵业有限公司（www.tajsby.cn）是从事“水泵,泥浆泵,混流泵,轴流泵,渣浆泵”的企业，公司秉承“诚信经营，用心服务”的理念，为您提供的产品和服务。欢迎来电咨询！联系人：刘经理。 产品：金石泵业供货总量：不限产品价格：议定包装规格：不限物流说明：货运及物流交货说明：按订单
